Atomm AIAtomm AICreative ToolsCreative ToolsMy WorkspaceMy Workspace
ProjectsProjectsTemplatesTemplatesDesignsDesignsMaterials LabMaterials LabMy FollowingMy FollowingHubsHubs

Stone & Slate Materials for xTool Laser Machines

Stone engraves; it does not cut. Slate, marble and soapstone all carry a thin dark skin over paler stone underneath, and the mark is simply that skin cleared away. It is a shallow job that needs very little energy — which is why a 10W diode handles it, and a 55W CO2 runs at 15% power rather than full.

xTool-tested stone — rectangular and square slate coasters, a round slate coaster, a marble and wood coaster and a set of soapstone whiskey stones
Browse the Stone catalogue

Five Tested Stones, 168 Maker Records

The tested set is small: a 4.5mm round rock coaster, black, white and dark-green marble, and soapstone whiskey stones.

Slate is the cheap way in — coasters start at $6.49 a set, six blank sheets run $25.99 to $36.99, nine soapstone whiskey stones $9.99.

Thickness clusters at 4.5, 5 and 6mm, and because nothing is cut through it only sets focus height.

Browse the Stone catalogue
A square slate coaster engraved with a maker studio logo by an Atomm maker on an xTool M2

Diode, Fiber, CO2 and UV All Work

Stone does not care much which wavelength hits it. The dark surface layer absorbs blue light, infrared and ultraviolet alike, so a diode, a fiber head, a CO2 tube and a UV laser all clear it — they just do it at very different speeds and power levels.

Coated or sealed slate is the one exception: the coating burns before the stone underneath ever marks.

See this slate record
A square slate plaque engraved with a detailed hobby-shop crest by an Atomm maker on an xTool F1 Ultra fiber head

Slate, Marble, Soapstone, Granite — Four Different Surfaces

All four engrave. What differs is the colour you reveal and how much power it takes.

Blank rectangular rock slate sheets sold by xTool

Slate

The default. Dark grey to black, 4.5-6mm, and the engrave lifts to a pale grey that photographs well. Splits along its cleavage planes, so clamp it flat rather than tight.

Black marble tile — Stone Materials for xTool Laser Machines

Marble

Polished and harder than slate. Black marble gives the strongest contrast of anything in the family; white and dark-green read softer because the frosted mark is closer to the base colour.

Soapstone whiskey stones — Stone Materials for xTool Laser Machines

Soapstone

Soft enough to scratch with a fingernail, which means low power and fast passes. The whiskey-stone cubes are the common format, and they take a small logo cleanly.

A granite memorial plaque engraved by an Atomm maker on an xTool P2S

Granite

Hard, speckled and usually thick. A maker ran 20mm granite on a P2S at 200 mm/s and 65% power; the speckle competes with fine detail, so bold artwork wins.

Which xTool Machine Is Best for Stone?

Every beam type works, so the real question is which machine the work has actually been done on. Of the 168 records, the six machines below carry 142: the M2 leads with 57, then the S1 and the F2 at 28 each.

xTool M2 — stone materials tested on it

xTool M2

57 stone records, the most of any machine. A 10W blue diode is enough: one maker ran a slate board at 120 mm/s and 55% power in a single pass.

xTool S1 — stone materials tested on it

xTool S1

28 records, mostly on the 20W and 40W diodes. More power means less of it: 5mm rock coasters run at 180 mm/s and 30% on the 40W.

xTool F2 — stone materials tested on it

xTool F2

28 records, tied with the S1. The 5W IR head engraved a 4.5mm slate coaster at 80 mm/s and full power.

xTool F1 Ultra — stone materials tested on it

xTool F1 Ultra

12 records on the fiber head. Fiber is the one route to relief work on stone: the embossment mode shows up here and on the F2 Ultra, nowhere else.

xTool F2 Ultra UV — stone materials tested on it

xTool F2 Ultra UV

15 records. Ultraviolet puts the least heat into the piece, which suits thin or already-finished blanks: 400 mm/s at full power on a 4.5mm coaster.

xTool P2S — stone materials tested on it

xTool P2S

2 records, and the only machine here with granite at 20mm on it. A 55W CO2 needs 15% power on a coaster, so the bed size matters more than the wattage.

Shop Slate, Marble & Soapstone Blanks

More

Stone Settings Recorded by Makers

The machine each job was run on, and the numbers that produced the result.

A grey slate board engraved with a finely detailed fantasy map

Grey Slate Stone Board

M2 (Blue light 10W) · Lasering on flat surface · Engrave · 1 pass · 120mm/s · 55% Fine linework on a 10W diode, one pass.

A square slate coaster engraved with two dog portraits

Square Rock Coaster

S1 (Blue light 40W) · Process on baseplate · Engrave · 5mm · 1 pass · 180mm/s · 30% Photo engraving on 5mm coaster stock.

A round black slate coaster engraved with a dartboard emblem

Black Slate Stone Coaster

F2 (Fiber IR 5W) · Process on baseplate · Engrave · 4.5mm · 1 pass · 80mm/s · 100% Infrared on slate: slow and full power.

A slate coaster carrying a raised crest in relief

Slate Coaster

F2 Ultra (Fiber IR 60W) · Embossment · Emboss · 3mm · 1 pass · 12000mm/s · 80% Relief, not engraving. Fiber only.

A round slate coaster engraved with a business logo

Round Rock Coaster

F2 Ultra UV (Ultraviolet light 5W) · Process on flat surface · Engrave · 4.5mm · 1 pass · 400mm/s · 100% Cold beam, least heat into the blank.

A round slate coaster engraved with an autumn design

Round Rock Coaster

P2S (CO2 55W) · Process on slats · Engrave · 4.5mm · 1 pass · 350mm/s · 15% A 55W CO2 wants 15% power, not more.

Why Start From a Tested Setting

Stone does not cut, so stop trying

The beam clears the dark surface layer; it does not sever the stone. If a setting chart promises a cut-through on slate, it is not describing this material.

The contrast is subtractive

You are removing a thin dark surface to reveal pale stone underneath. Past a certain power the surface powders instead of clearing, and the mark goes grey and dusty rather than white.

Coated and sealed slate is a different material

Many retail coasters ship with a sealant or a painted back. The coating burns before the stone marks, so a value recorded on raw slate will look wrong on a finished one.

Flatness matters more than thickness

Nothing is being cut through, so thickness only sets focus height. A bowed or uneven blank changes that height mid-pass, which is what most patchy engraves turn out to be.

Explore the Materials Lab

Nine laser material families from the Atomm Materials Lab

All laser materials

Wood, acrylic, leather, metal, glass, stone and the rest — eleven material families with official settings.

Nine laser wood surfaces — basswood and birch plywood edges, walnut, mahogany, cherrywood, bamboo and MDF

Wood, plywood and MDF

Forty boards from basswood ply to oiled MDF. Grade decides the cut, species decides the look.

Nine tested glass and crystal materials — a K9 crystal ball, inner-carved block, heart keychain, pink K5, frosted glass jars, cobalt glass and an arch crystal with a clock

Glass and K9 crystal

Crystal blanks, glassware and awards — plus why 3D inner engraving needs a UV laser.

Nine packaging and display items — a five-tier jewelry stand, iridescent gift box, pink jewelry box, LED writing board, black floating frames, a jewelry bag, a lilac frame, a walnut box and an origami display table

Packaging and display

Gift boxes, floating frames, jewelry displays and kraft bags — the part a customer sees before the work.

Stone Engraving Guides & Ideas

Which stone takes a mark, what to expect from slate versus marble, and designs makers have already run.

21 Free Personalised Slate Coaster Ideas

21 real personalised slate coaster designs from the Atomm community — sports teams, zodiac signs, military badges, and pet breeds, free to preview and export.

2026/07/181620

25 Free Stone Coaster Ideas

Browse 25 free stone coaster ideas from real Atomm community projects — engraved stone, black stone, and marble coasters with pop-culture, wildlife, and gift themes to preview and cut.

2026/07/141205

16 Free Marble Coaster Ideas

Discover 16 free marble coaster designs from the Atomm community — real marble, white marble, and marble-and-wood coaster sets, hexagon and square shapes. Preview, edit, and export free.

2026/07/141026

30 Free Pet Portrait Ideas (Laser-Engraved Dog & Cat Portraits on Wood, Acrylic & Slate)

Discover 30 free laser-engraved pet portrait ideas for dogs and cats on wood, slate, acrylic, crystal, and metal, from keychains and coasters to memorial plaques.

2026/08/211430

Laserable Materials: The Complete List of What You Can Laser Cut and Engrave

A complete list of laserable materials: what a laser cuts through, what it can only mark, which laser type each one needs, and what you must never cut.

2026/08/252035

xTool Materials: The Complete Guide to Tested Laser Materials

Every material xTool lasers cut, engrave and mark, what xTool officially sells, and what the xTool Selected badge and its QR settings really give you.

2026/08/272338

FAQs

Can a laser cut slate or stone?

No. The mark on stone is the thin dark surface layer being cleared away, not material being parted — stone is too dense and mineral for a laser to cut through. Cut slate to shape with a wet saw, or buy blanks already cut.

What laser do you need to engrave slate?

What settings should I start with on a slate coaster?

Why does my slate engrave look grey and dusty instead of white?

Does marble engrave like slate?

Can you emboss or make relief on stone?

Engraving stone? Start from a blank and a setting that were measured

Open the stone catalogue