xTool Materials: The Complete Guide to Tested Laser Materials

Atomm
Atomm·Follow
2338
0
0
Published 2026/08/27
Six xTool-tested laser material families: wood, vinyl film, glass, canvas, anodized metal and slate
The xTool material catalogue is organised into families, most of which carry xTool-tested entries, from basswood plywood to K9 crystal.

Search for xTool materials and three different questions come back tangled together. What can an xTool laser physically cut or engrave? What stock does xTool actually sell? And what is that "xTool Selected" badge on the packaging worth?

They are related questions, but they are not the same one, and mixing them up is how people end up with a sheet their machine cannot touch.

This guide takes them one at a time. First the honest capability list, split by laser type, because a diode machine and a fiber machine barely overlap on metal. Then the official catalogue, family by family, with real product examples.

Then what xTool Selected gives you in practice: power, speed and pass values recorded on real machines, and a QR code that configures the laser for you. All of it is drawn from the Materials Lab, where official test parameters and community-reported settings are published side by side.

Key Takeaways

  • xTool lasers cut wood, plywood, MDF, acrylic, leather, PU, fabric, felt, paper, card, cork and laser rubber. Metal, glass, stone, ceramic and coated drinkware get engraved or marked, not cut.
  • Laser type decides the material list far more than wattage does. A diode marks anodized and coated metal, and on most bare metal it wants a marking spray or an IR or fiber module — though xTool lists stainless steel among the S1 diode’s engravable materials, so check your own model. A fiber or infrared module marks bare metal directly; CO2 covers the widest range of organics.
  • "xTool Selected" is not a quality grade. It means the material has been run in the xTool lab, so it carries recorded power, speed and pass values per machine model, plus a QR code on the pack that supported machines scan to set themselves up — support depends on the model and software version, so check yours.
  • Where xTool has no data, the Materials Lab Community tab holds settings makers recorded themselves on third-party stock. Unverified, but often the only record that exists.

What "xTool Materials" Actually Means

Inside the Materials Lab, material is filed under three tabs, and the difference between them is entirely about parameters. Not price, not quality, not who made the sheet.

TabWhat it holdsTested settings?QR auto-setup?
Official
(xTool Selected)
Stock xTool sells and has run through its own labYes — power, speed and passes per machine model, with a last-updated dateYes, on models and software versions that support it
CommunitySettings makers recorded themselves on stock they sourced anywhereYes, but self-reported and unverifiedNo
AccessoriesGeneral add-ons and fixtures, plus printing-line consumablesNo laser parameters published in this tabNo

The practical consequence is simple. On the Official tab you start from a number somebody measured. On Community you start from a number somebody reported. On Accessories there are no published laser values to start from, so you dial it in yourself.

All three are worth browsing directly: the Official tab for xTool Selected stock with recorded parameters, the Community tab for maker-recorded settings on third-party material, and the Accessories tab for fixtures, add-ons and the printing-line consumables.

That is also why a laser marking spray or a rotary attachment sits under Accessories rather than Official. Useful kit, but there is no "correct power for a rotary attachment" to record.

Materials xTool Lasers Can Cut and Engrave

Most of the material families carry xTool-tested parameters; a couple sit in the catalogue with nothing recorded against them yet. What is live on the Official tab moves as new stock goes through the lab, so treat the tab as the source and the table below as a shape rather than a count.

Grid of the xTool-tested material families and the relative depth of each one
Wood, metal, leather, fabric, paper and vinyl are the deep xTool-tested families; glass, stone and rubber are much smaller sets.

Materials a laser cuts all the way through

Everything organic and thin belongs here: basswood and birch plywood, MDF, hardwood, bamboo, cast acrylic, top-grain and PU leather, felt, coated canvas, denim, cotton, kraft and shimmer card, cardboard, cork and laser stamp rubber.

These absorb laser light readily and vaporise instead of melting, which is what a clean cut edge actually requires. Wood is one of the largest families for a reason — it is forgiving, cheap, and the recorded values are a usable starting point across machines. Our wood selection guide goes deeper on species and plywood grades.

Materials Commonly Engraved or Marked

Metal, glass, stone, slate, ceramic and coated drinkware are all in the catalogue, and on these machines the job is a surface change rather than a cut: annealing steel, frosting glass, ablating a coating, burning contrast into slate. Metal is the one that needs an asterisk. Parting metal is work for a dedicated metal cutter, and xTool’s own F2 Ultra UV comparison lists no metal cutting — yet a handful of community-recorded jobs do show thin sheet cut through on a UV head, from 0.1mm brass in two passes up to 0.5mm stainless in sixty. Read those as slow micro-machining experiments, not a capability to plan a product around.

That is not a limitation so much as the whole point of these families. A slate coaster or an anodized aluminum tag needs a surface mark, not a hole. If you want the mechanics of that, we cover it in engraving metal and engraving glass separately.

The awkward middle: films, silicone and plastics

Vinyl and film is one of the deeper families, covering self-adhesive, holographic, inkjet and sublimation stock. It cuts beautifully — as long as it is not PVC vinyl. Same word, completely different chemistry.

Silicone — sheet, watch bands, phone cases — engraves well and tolerates a lot. ABS is in the catalogue as two-tone engraving laminate. It smears rather than cutting, so treat it as engrave-only, run extraction, and do not assume unknown ABS stock behaves like the laminate.

Check the spec sheet, not the label. "Vinyl" on a craft store shelf can mean PVC or it can mean PET or polypropylene. The first one releases hydrogen chloride in a laser. If the supplier will not tell you the polymer, treat it as PVC and leave it alone.

Which xTool Machine Handles Which Material

This is where most material mistakes actually happen. People compare wattage across machines when the number that decides the material list is the wavelength.

Six xTool laser machines with their laser type and the materials each one handles
Six current xTool machines and the material list each laser type opens up.

A 40W diode and a 40W CO2 tube are not interchangeable. The diode struggles with clear acrylic because the beam passes straight through it; the CO2 cuts it cleanly. Neither is the natural choice for bare stainless steel, which is usually a fiber or infrared job — though xTool does list stainless steel among the S1’s diode-engravable materials, so check your own model.

Laser typeWavelengthWhat it processesWhat it will not do
CO210.6 µmWidest organic range: wood, MDF, acrylic (clear included), paper, leather, fabric, cork, rubber. Frosts glass and stone.Bare metal
Diode450–455 nmWood, dark acrylic, leather, felt, card, and anodized or painted metal; xTool also lists stainless steel as diode-engravable on the S1Clear acrylic
Fiber / MOPA1064 nmBare and coated metal — stainless, brass, aluminum, titanium. MOPA adds colour marking on steel.Wood, clear plastics
Infrared (IR)1064 nmMetals and many plastics at modest power; the usual module for coated drinkwareThick organics
UV355 nmCold marking on glass, ceramic, plastics and coated metal with minimal heat damageCutting anything but the thinnest sheet

Because of that split, every material card in the Materials Lab lists the machine models it has actually been tested on rather than a single generic setting.

If your exact model is not on the list, the closest machine of the same laser type is the sensible place to start, but not a substitute: power, spot size, lens and the material batch all differ, so re-test before a batch.

If you are still choosing hardware, the CO2 versus fiber versus diode comparison walks through the trade-offs from the machine side rather than the material side. And whether a diode can engrave metal is worth reading before you buy for metal work.

Each family now has its own breakdown, machine by machine: F series, M series, P series, D series and the S1.

What xTool Officially Sells

The official catalogue is deliberately narrow. It is not a general material store; it is the set of stock xTool has put through parameter testing, so every sheet in it ships with numbers attached.

Alongside sheet stock it carries finished parts too — engravable jewelry blanks arrive already cut, drilled and evenly finished, so only the engraving is left to do.

FamilyTypical official stockCatalogue depth
Wood, plywood & MDFBasswood plywood sheets, birch plywood, coloured MDF board, hardwood, bambooDeep
Acrylic & plasticMirror acrylic, translucent glossy sheet, two-tone and glitter acrylic, engraving laminateDeep
Metal & anodized aluminum304 stainless sheet, anodized aluminum, brass, metal business cards, card holdersDeep
Leather & PUTop grain cowhide, crazy horse, nappa, gradient PU, laserable PU notebooksDeep
Fabric & feltCanvas and jute tote bags, felt board, coated canvas, denim, cottonDeep
Paper & cardstockShimmer and kraft card, gift card envelopes, photo paper, cardboardDeep
Vinyl & filmHolographic inkjet sticker paper, self-adhesive vinyl, sublimation filmDeep
Glass & crystalK9 crystal blanks, frosted and high-temperature glass, drinkwareShort list
Stone & slateMarble, a rock slate board and saponite whiskey stonesShort list
SiliconeGradient sheet, watch bands, phone casesMid-sized
RubberLaser stamp sheetShort list
Ceramic, cork, magnet & moreSublimation-coated ceramics, cork coasters, adhesive magnetic sheet, braille sticker stockMid-sized

Buying happens on the xTool store — the xTool Selected materials page is the storefront side of the same catalogue. Availability is not identical in every region, so a sheet listed in the US store is not guaranteed to be stocked in the EU or Japan.

Check the store’s current terms before you count on a return: xTool’s published refund policy states that materials purchased separately cannot be returned, and the 30-day window it describes applies to eligible products, with service fees after the first 14 days.

What "xTool Selected" Actually Means

xTool Selected is the badge on official material, and it is worth being precise about what it certifies. It does not claim the wood is better wood. It claims the material has been measured.

xTool material QR code explainer showing coloured acrylic sheets each carrying a scannable code
Every xTool Selected pack carries a QR code that hands the tested parameters to the machine.

The QR code on the pack

On a machine that supports the scan, you place the sheet, scan the code, and the tested power, speed and pass values for that exact material and thickness load themselves.

Support is a property of the model and the software version rather than of the hardware on the lid, so check yours in XCS rather than reading it off the spec sheet. Where the scan is not available, the same numbers are on the material page and you send them to xTool Studio or XCS by hand. Same values, one extra step.

The numbers behind the badge

Infographic showing 800+ recorded material parameter sets and 10,000+ parameter effect previews
What the badge is actually selling: recorded parameter sets, plus previews of what each one looks like on the material.

A material carries one recorded combination per machine model, thickness and process it has actually been through, so a widely tested sheet carries many and a narrow one carries few. The Materials Lab holds roughly a thousand xTool-tested entries spread across the material families, and can be filtered by xTool laser model. Both the totals and the model list move as stock and machines are added, so read the tab itself rather than any figure quoted here.

Each material also shows the date its parameters were last updated. That is the field to check before you trust a number — a two-year-old entry for a machine that has had firmware changes deserves a test cut first.

What the badge does not mean

It does not lock the material to xTool hardware. Plywood is plywood and anodized aluminum is anodized aluminum, so a Glowforge or an OMTech will cut the same sheet perfectly well.

What is xTool-specific is the recorded settings. On another brand, match the laser type first, then the rough wattage, then run a small test grid before committing a full sheet. Our speed and power testing guide covers how to build that grid.

When xTool Has Not Tested It: Community Settings

The xTool-tested catalogue runs to around a thousand entries. The stock makers actually buy is effectively unlimited, and no manufacturer records laser settings for a random sheet of birch from a local yard.

That gap is what the Community tab fills. Makers publish the material, the machine, the thickness and the exact numbers they landed on, and the community-recorded set now runs into the thousands. Here is what one entry looks like in practice.

Speed and power test grid engraved into birch plywood showing the usable range
A 3/16" (4.5mm) birch plywood record: xTool S1, engrave, 1 pass, 300 mm/s at 50% power. 3/16" (4.5mm) Birch Plywood →

Note what the record carries: not "birch plywood works", but a thickness, a machine, an operation and three numbers. That is the difference between a settings library and a material list.

Golf swing figure embossed into a brass coin with a fiber laser
Brass, embossed on an xTool F1 Ultra at 900 mm/s and 90% power over 2 passes. Brass coin →

Brass is a good example of why the community data matters. It is a bare metal, so it needs a fiber or IR source, and the coin blank a maker buys is never the exact stock in a test lab.

Monogram engraved into the side of a frosted green glass coupe
Frosted glass, engraved on an xTool F1 Ultra at 40 mm/s and 40% power over 2 passes. Frosted Clear Glass →

Glass is the family where community records help most, because thickness, curvature and coating all shift the result and the xTool-tested glass set is a short one.

Treat community numbers as a strong starting point rather than a specification. They were recorded by one person on one sheet, and they will still save you most of the guesswork.

Materials You Should Never Put in an xTool

Some materials are not a settings problem. No power level makes them safe, because the failure mode is toxic gas or fire rather than a poor cut.

Warning panel listing six materials that must never be laser cut and the reason for each
These six are hard no-go materials on any laser, regardless of wattage or extraction.

PVC is the headline case. Its chlorine content turns into hydrogen chloride gas under the beam, which is toxic to breathe and corrodes the machine from the inside out. The damage is cumulative and invisible until something fails.

Polycarbonate is the most common honest mistake, because it looks exactly like acrylic on a shelf. It absorbs the beam poorly, yellows, chars and burns instead of cutting. If the sheet is labelled Lexan, it is polycarbonate.

The rest of the list is about the same principle: unknown coatings, fibreglass and carbon-fibre composites, and PTFE all release something you do not want in the room. We go into the detail in what different materials give off when you cut them, and the broader safe material list is worth a read before you buy anything unfamiliar.

How to Choose the Right xTool Material

Working backwards from the job rather than from the catalogue tends to get you there faster. A few common starting points:

New to lasers and want a result today. Basswood or birch plywood at 1/8" (3mm). It is the most widely recorded starting material, the entries are dense, and a scorched sheet costs almost nothing — how thick your own machine cuts is in its published spec. Coasters, signs and boxes all live here.

Selling personalised gifts. Slate coasters and anodized aluminum tags give high contrast with almost no fuss, and both engrave rather than cut, so throughput is fast. The xTool-tested Stone family is a short list — marble, a rock slate board and saponite whiskey stones — and the community tab is where most slate numbers live.

When the brief calls for something transparent, cast acrylic on a CO2 machine is the reliable route — a diode will fight clear sheet no matter how you set it. And for anyone marking bare stainless or brass, the question is not which material but which laser: fiber, MOPA or an IR module.

Working with client-supplied stock. Identify the polymer or the coating before anything else, then look for it on the Community tab. If nobody has recorded it and the supplier cannot tell you what it is, decline the job rather than guessing.

Run a test grid on any new material, tested or not. Ten minutes and a scrap offcut is cheaper than a ruined sheet, and it catches the variables no database can hold — your extraction, your lens condition, the age of your diode. A kerf offset test is worth adding whenever parts need to fit together.

Final Thoughts

The useful way to think about xTool materials is as two different products. There is the physical stock, which is not special and which any laser of the right type can process. And there is the parameter data attached to it, which is the part you are actually paying for when you buy official material.

On the models that support it, the QR workflow removes most of the setup step. Check your own model in XCS rather than assuming a camera is enough.

If it does not, you are still starting from a measured number instead of a forum guess. And when the catalogue does not cover what you have, the community library usually does.

Two neighbouring pages are worth a look if your work spans both sides of the lab: the printing materials and supplies hub for UV, DTF and screen printing consumables, and the combined laser and printing materials overview if you are not sure which route a job takes.

Frequently Asked Questions about xTool Materials

What materials can xTool machines cut?

Wood and plywood, MDF, cast acrylic, leather and PU, fabric and felt, paper and card, cork, laser rubber and non-PVC films all cut through. Metal, glass, stone and ceramic are engraved rather than cut. Which of those your machine can handle depends on its laser type, and every material card lists the models it was tested on.

What is xTool Selected material?

It is xTool’s own lab-tested stock. The badge means the material has been run in the xTool lab, so it carries recorded power, speed and pass values per machine model, a last-updated date, and a QR code on the pack. It is a statement about the data, not a quality grade for the sheet.

Can I use xTool Selected materials on a Glowforge or another brand?

Yes. The sheet is ordinary plywood, acrylic or anodized aluminum and no machine can tell where you bought it. Only the settings are xTool-specific, since they were measured on xTool hardware. Match the laser type first, then the approximate wattage, then run a small test grid before you commit a full sheet.

Can an xTool diode laser engrave metal?

Mostly not, but it depends on the model. A diode’s reliable metal work is anodized aluminum, painted or powder-coated metal, and metal treated with laser marking spray — in each case it is removing or reacting with a surface layer. Bare brass and titanium are a fiber, MOPA or infrared job. Stainless is the exception worth knowing: xTool lists it among the S1 diode’s engravable materials, so read your own model’s spec before assuming bare metal is off the table.

How current are the tested settings?

Every material page shows the date its parameters were last updated, which is the field to check before trusting a value. Machines get firmware updates and diode modules age, so an older entry is a good starting point rather than a guarantee. A quick test cut on a scrap resolves it either way.

What is the difference between Official and Accessories in the Materials Lab?

Official is the tested set: every entry has recorded parameters per machine model and a scannable pack. Accessories is the tab that does not publish laser parameters, including fixtures, rotary attachments, marking spray, and the printing-line consumables such as screen-printing inks and DTF bundles. All useful, but on those you dial the settings in yourself.

Start from a tested setting, not a guess

Browse the xTool-tested material catalogue by family or by machine, then send the recorded parameters straight to your laser.

Contents
What "xTool Materials" Actually Means
Materials xTool Lasers Can Cut and Engrave
Which xTool Machine Handles Which Material
What xTool Officially Sells
What "xTool Selected" Actually Means
When xTool Has Not Tested It: Community Settings
Materials You Should Never Put in an xTool
How to Choose the Right xTool Material
Final Thoughts
Frequently Asked Questions about xTool Materials
gift