Boucles d’oreilles Lotus ajourées – Plywood 3mm – D1 Pro 20W || Open Lotus Earrings – 3mm Plywood – D1 Pro 20W
Instruction
Information
FR
Lightweight, openwork earrings made of 3mm poplar plywood, open lotus pattern with built-in attachment hole (1.8mm).
Optimized for the xTool D1 Pro 20W with 2-pass cutting to reduce abrasion and maintain sharp edges.
Height: 48mm (adjust to preference).
EN
Lightweight openwork lotus earrings in 3 mm poplar plywood, with integrated hanging hole (1.8 mm).
Optimized for xTool D1 Pro 20W with 2 cutting passes to avoid burning and ensure clean edges.
Approx. height: 55–60 mm (adjustable).
Instruction
Step1
Instructions (EN)
Materials & tool
- 3mm
poplar plywood- Honeycomb tray, Air Assist ON-
Masking tape (optional, limits streaks)
- 6–8mm junction rings + ear hooks
Before casting
1. Import the file into xTool Creative Space (ATOMM).
2. Check the scale: target height 48–55mm; attachment hole≈ 1.6mm.
3. Laser Flat Mode, 3mm Plywood Material.
4. Cutting layer: 0.01 mm vector contours, without infill.
5. Focus: automatic or 3mm gauge.
6. Attach the wood to the honeycomb (option: masking tape).
7. Frame to check the position.
Recommended settings
- Power 20w: 100 %
- Speed: ≈ 7 mm/s- Passes
: 1
- Air Assist: ON
Cutting
1. Throw the **1st pass**, monitor the cut (never unattended).
2. Let the smoke dissipate for 2–5 sec, then perform the **2nd pass**.
3. Check that the part is coming off. If necessary: repeat 1 pass at slightly faster speed.
Finishing & Assembly
1. Remove the tape, wipe the edges (ISO alcohol). Fine sanding if necessary.
2. Option: apply varnish/oil.
3. Cast on a 6–8 mm ring and hook. Open/close laterally.
4. For a perfect duo, mirror a piece before cutting.
Quick troubleshooting
- Dark edges→ increase speed, keep 2 passes, enable Air Assist, masking tape.
- Does not cut through → redo 1 pass or reduce speed (−10–20%).
- Marks underneath → use honeycomb + wedges.
Safety
- Never leave the machine unattended.
- Keep a water/CO₂ spray on hand.
- Mandatory ventilation.
---
Instructions (EN)
Materials & tools
- 3 mm poplar plywood
- Honeycomb panel, Air Assist ON-
Painter's tape (optional, reduce burn marks)
- 6–8 mm jump rings + ear hooks
Before you start
1. Import the file into xTool Creative Space (ATOMM).
2. Check scale: target height 48–55mm; hanging hole ≈ 1.6 mm.
3. Select Laser Flat, material Plywood 3 mm.
4. Cut layer: vector 0.01 mm stroke, no fill.
5. Focus: Auto or 3mm gauge.
6. Secure the plywood on honeycomb (optional tape).
7. Frame the job to confirm placement.
Suggested settings
- Power 20w: 100 %
- Speed: ≈ 7 mm/min
- Passes: 1
- Air Assist: ON
Cutting
1. Run the **first pass**, watch the cut (never leave unattended).
2. Let smoke clear for 2–5 s, then run the **second pass**.
3. Check if parts fall out. If not, add one more pass at slightly higher speed.
Finishing & Assembly
1. Remove tape, clean edges (isopropyl alcohol). Light sanding if needed.
2. Optional seal/varnish for protection.
3. Attach a **6–8 mm jump ring** and ear hook. Open/close sideways.
4. For a matching pair, **mirror** one before cutting.
Quick troubleshooting
- Dark edges → increase speed, keep 2 passes, enable Air Assist, tape the top.
- Not cutting through → add 1 pass or lower speed (−10–20%).
- Burn marks below → honeycomb + small spacers.
Safety
- Never leave the laser **unattended**.
- Keep water/CO₂ nearby.
- Ensure **proper ventilation**.
