Haru Studio

Report

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie — Project made with xTool M1 Ultra machine for Laser cut and engrave.

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie — Project made with xTool M1 Ultra machine for Laser cut and engrave.

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie — Project made with xTool M1 Ultra machine for Laser cut and engrave.

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie

[Laser cut and engrave] Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie

Laser Engraved Wooden Dog Themed Bookmark with Paw Prints Border Collie

Instruction

Border Collie Bookmark.xcs

Border Collie Bookmark

.xcs

Application scenario

Laser processing

Machine & module

xTool M1 Ultra

10W

Compatible xTool Machine

New

M2

10W, 20W

F2 Ultra UV

5W

F2

15W

P3

80W

F2 Ultra

40W

F1 Ultra

20W

M1

5W, 10W

D1

5W, 10W, 20W

D1 Pro

5W, 10W, 20W, 40W

P2

55W

F1

10W

S1

10W, 20W, 40W

M1 Ultra

20W

P2S

55W

Accessories

xTool M1 Riser Base with Honeycomb Panel

xTool M1 Air Assist Set

Material used

1/8"(3mm) Basswood Plywood

gift

34

795

Information

      This project provides a simple and original instruction for engraving and cutting wooden bookmarks using the xTool M1 Ultra (10W diode laser).
The instructions are based on my own setup and testing, focusing on practical use, machine configuration, and common checks before running the job. The bookmark size can be adjusted freely to match personal preference or project needs.
Please note that the default settings are optimized for basswood plywood. If you choose a different material, the laser settings will need to be adjusted accordingly, and results may vary if parameters are not recalibrated.
Before starting, make sure the file includes separate Engrave and Cut operations, as the software may occasionally consolidate them automatically.

reading accessory

Instruction

1

Step1: Machine Set up

⚠️ Important:
If you change the material, the default settings included in this file will also need to be adjusted.
Using a different wood, MDF, or acrylic may result in poor or unsatisfactory results if the parameters are not recalibrated.

XCS may sometimes automatically consolidate operations.
Before running the job, verify that Engrave and Cut are still separated, and manually reassign them if needed.

Power ON the xTool M1 Ultra
Install the honeycomb bed
Place the wood sheet on the honeycomb
Secure material using magnets, ensuring flatness

2

Step2

Open xTool Creative Space (XCS)
Import the bookmark file
Position the design within the material area
Perform Auto Focus
Use Frame to confirm alignment

3

Step3

Acceptance Criteria

Engraving is clear and legible
Consistent engraving depth
No excessive burn marks
Clean cut-through edges
Bookmark dimensions per design

4

Step4: Finishing & Storage

FINISHING (IF APPLICABLE)

Light edge sanding (grit 220–320)

Clean engraving residue

Optional sealing or oil finish

STORAGE

Store bookmarks flat

Protect from moisture and bending

Avoid stacking without separators

Comments

Remixes

License

This work contains AI-generated content.

You may also like

The Dog Paw Mandala

dog paw split mandala