Question 1

What is the Paper Flower Generator and how does it work?

Accepted Answer

It is an online tool that turns parametric designs into print-and-cut files for paper flowers. You pick from 47 pieces across four libraries — flowers, leaves, sprigs, and stamen accessories — set the finished size and your paper thickness, and the generator solves the geometry, shows the assembled flower in 3D, and exports 1:1 SVG cut paths with matching print artwork into xTool Studio.

Question 2

Will the finished flower really be the size I type in?

Accepted Answer

Yes — the parameters solve for the finished piece. A rolled rose works out its number of turns from your paper's thickness, and a fringed centre works out its strip length from the target diameter, so the same design comes out correct on 120 gsm and 300 gsm alike. If a shape cannot physically reach the size you asked for, the generator reports what it actually achieved instead of quietly cutting something smaller.

Question 3

What paper should I use?

Accepted Answer

Cardstock is the working material — set its real thickness in the generator and the turn counts and strip lengths adapt to it. Lighter paper rolls more turns for the same rose; heavier card holds bigger, sculptural petals. Whatever you use, print the artwork on it first, then cut, so the print and the 1:1 cut paths stay aligned.

Question 4

What's in the four libraries?

Accepted Answer

47 starting points in total: 12 flowers from rolled roses to layered blooms, 8 leaves, 16 sprigs for filler and texture, and 11 accessories — 4 calyx bases and 7 stamen centres. Every entry loads with preset sizes and colors, and each one can be reshaped with the parameter sliders before you export.

Question 5

Is the 3D preview exactly what I'll make?

Accepted Answer

Treat it as a faithful guide to shape and proportion rather than a render of your hands' work. The preview shows petals cupping, fringe rolling into a pompom, and leaves folding along the midrib, with a score line on the paper for every move — but how tightly you roll and curl varies from person to person, as does the stiffness of your card. The cut paths themselves are the precise part, at exactly 1:1.

Question 6

How do I assemble the flowers?

Accepted Answer

Each part comes with a How-to-assemble guide: a video plus written steps that match the exact cut file you exported — roll the spiral from the outer end, offset each layer by half a petal, keep the fringe spine at the bottom. The steps are written for the specific piece you're making, not a generic flower tutorial.

Question 7

What machines can cut the files?

Accepted Answer

The export lands in xTool Studio, so xTool cutting machines run the files directly. Before any path reaches your machine, the generator preflights blade spacing, minimum slit width, and minimum inner corner radius against what a real blade can cut — delicate sprigs pass the same checks as bold petals. The materials section on this page lists paper and cardstock that suit print-and-cut flowers.

Question 8

Can I sell flowers I make with it?

Accepted Answer

Many makers use generators like this to run custom orders — quote a size and palette, tune the sliders, cut the same evening. Before selling, review Atomm's terms of use for the latest guidance on commercial use. Because sizes are repeatable, a design approved once can be re-cut identically for every order that follows.

Question 9

Is the Paper Flower Generator free to use?

Accepted Answer

You can open the generator for free, browse the four libraries, tune parameters, and preview flowers in 3D. Generating and exporting use Atomm credits, with the first try free and the cost shown before you commit. Invite friends to register and both of you earn extra credits.

Generátor papírových květin

Jak to funguje

Vyberte si z čtyř knihoven

Nastavte hotovou velikost a váš papír

Exportovat a sestavit

Výběr správného materiálu pro váš projekt

Požádejte o 90 mm a soubor pro řezání dodává 90 mm

47 Květy, Listy, Výhonky a Střediska, Připravené k Ladění

Sledujte, jak to zkroucit, otočit a složit, než to ustřihnete

Cesty pro řezání a montáž předletového kontrolování, které odpovídají souboru

Kdo pěstuje tyto zahrady

Svatební a párty stylisté

Dárceři pro ni

Věnec a výrobci domácího dekoru

Prodejci řemesel a zakázkové objednávky

Začněte s Atomm Craft Lab dnes

Nejčastější dotazy

Co je to generátor papírových květin a jak funguje?

Bude hotový květ opravdu tak velký, jaký napíšu?

Jaký papír bych měl použít?

Co je ve čtyřech knihovnách?

Je 3D náhled přesně to, co vyrobím?

Jak mám sestavit květiny?

Jaké stroje mohou řezat soubory?

Mohu prodávat květiny, které s ním vyrábím?

Je Papírový květinový generátor zdarma k použití?

Pozvěte přátele k registraci a oba získáte kredity.