Atomm

Report

Project made with xTool P2 machine for Laser cut and engrave.

Acrylic Sound Control Light

Instruction

AcrylicSoundControlLight

.xcs

Show 1 more

Application scenario

Laser processing

Machine & module

xTool P2

55W

Material used

3mm Black Acrylic

5mm Clear Frosted Acrylic

2 ft RGB LED strip

RGB LED controller

IR remote control

1339

Information

        - The acrylic sound control light is a nice and practical handicraft. Being simple and elegant, it is assembled from sturdy acrylic sheets with strong light transmittance. The acrylic material allows it to cast a soft light when illuminated. 

  - In sound control mode, it can detect sounds and convert sounds into changes in light. Both melodies and conversations can be detected and uniquely represented through lighting effects. This mode also provides features such as adjustable brightness and color variation, enhancing the joy of life.

  - It is an exquisite handicraft that exudes a sense of technology. Being original and practical, it is an ideal decoration in modern life.

Bill of Materials

xTool parts

1/8" Black Frosted Acrylic (1pcs)/45991

1/5" Clear Frosted Acrylic (1pcs)/45991

2ft RGB LED Strip/45648

RGB LED Controller ＆ IR Remote Control/45648

* Currently only available in US store

Instruction

Step1: Prepare the following materials

3 mm Frosted black acrylic sheet × 1

5 mm Transparent frosted acrylic sheet × 1

2 ft RGB LED strip × 1

RGB LED controller × 1

IR remote control × 1

Scissors × 1

Glue × 1

Step2

Open the XCS file in xTool Creative Space, and laser engrave and cut the acrylic sheets. After processing the 3 mm frosted black acrylic sheet, select "3 mm acrylic sheet" on XCS, switch the canvas to "5 mm acrylic sheet", and process the 5 mm transparent frosted acrylic sheet.

Step3

After processing, remove the cutouts from your machine as shown in the images.

Step4

Refer to the part numbers in the XCS file. Insert one P-2 into a hole of P-1 as illustrated.

Step5

Place one P-3 onto the P-2, and push the P-3 downward until it clicks securely in place.

Step6

Repeat the previous steps until the sound control light's main body is assembled.

Step7

Prepare P-4, P-5, and P-12. P-12 will help attach P-5 to P-4.

Step8: Insert P-4 into P-12.

Step9

Apply glue to P-4. Place P-5 onto P-4 as illustrated. Press down on P-5 for 5 seconds. Remove P-12.

Step10

Insert the P-4 and P-5, which have been stuck together, into the light's main body as illustrated.

Step11

Apply glue to the edges of P-7. Align and attach P-7 to the groove at the top of the light's main body. Press P-7 firmly into place for 5 seconds to secure it.

Step12

Attach one P-8 to the bottom of the light's main body as illustrated, and apply glue to the joint to secure the P-8. Apply glue to any part of another P-8, then attach it to the previously attached P-8. Press firmly on the second P-8 for 5 seconds to ensure a strong bond. Repeat these steps to attach the third P-8 to the second P-8.

Step13

Remove the protective film from the back of the RGB LED strip, then align the strip with the engraving marks on P-6 and attach it in the direction as illustrated. At the edge of P-6, bend the strip and attach the remaining part of the strip along the back of P-6.

Step14

Align the scissors with the cutting position on the strip as illustrated. Ensure that you are cutting approximately 3 LED beads at the rear of the strip to remove the excess.

Step15

Insert the strip into the light's main body as illustrated, then press firmly down on the strip to secure it.

Step16

Flip the light's main body over. Apply glue to P-9, then align and attach it to the corresponding position on the light's main body as illustrated. Press P-9 firmly for 5 seconds to ensure a strong bond.

Step17

Apply glue to P-10, then align and attach it to the base of the light as illustrated. Press P-10 firmly for 5 seconds to ensure a strong bond.

Step18

Apply glue near the edges of P-11, then insert it into the light's main body in the direction as illustrated. Press P-11 firmly for 5 seconds to ensure a strong bond.