Report

[Laser cut and engrave] Abanico Llum d'Alhambra — Project made with xTool S1 machine for Laser cut and engrave.

Alhambra Light Fan

Instruction

Abanico Llum dAlhambra

.xs

Application scenario

Laser processing

Machine & module

xTool S1

40W

Material used

1.5 mm solid beech board, lightweight, resistant and suitable for precision laser cutting and engraving. Its thin thickness allows you to create delicate rods for fans, maintaining flexibility, detail and an elegant finish in natural wood.

421

Information

      ENGLISH
Llum d'Alhambra is a wooden fan inspired by the elegance of arabesque motifs and the beauty of traditional latticework. Its design combines radial lines, ornamental stars and delicate geometric openwork that create a light, harmonious piece full of detail.

Made of natural wood by Calados Vázquez, this fan combines craftsmanship, precision and contemporary design. Each rod provides visual rhythm and each fretwork lets light through, turning the wood into a decorative, functional and unique piece.

A range designed for those who value careful work, the beauty of the details and the personality of an artisanal creation.

ENGLISH
Llum d'Alhambra is a wooden fan inspired by the elegance of arabesque patterns and the beauty of traditional latticework. Its design combines radial lines, ornamental stars and delicate geometric cut-outs, creating a light, harmonious piece full of detail.

Crafted in natural wood by Calados Vázquez, this fan brings together craftsmanship, precision and contemporary design. Each rib adds visual rhythm, while each cut-out allows the light to pass through, transforming the wood into a decorative, functional and unique piece.

A fan created for those who appreciate careful craftsmanship, refined details and the character of a handmade design.

Instruction

Step1

Project carried out by Calados Vázquez.

Material used

1.5 mm solid beech board, lightweight, resistant and suitable for precision laser cutting and engraving.

Its thin thickness allows you to create delicate rods for fans, maintaining flexibility, detail and an elegant finish in natural wood.

Tools needed

xTool 40W
xTool Creative Space
Air Assist
Base honeycomb
Fume extractor or good ventilation
Fine sandpaper grit 320 or 400
Dry cloth or soft brush
Pin, screw or rivet for the center shaft
Small washer, optional
Wood wax, oil or varnish

File preparation

Open the fan file in xTool Creative Space.
Check that all the revarillas are complete.
Separate the cut and burn lines.
Check for duplicate lines.
Check especially the inner fretwork, the stars, the central shaft and the outer rod.
Adjust the layout to the size of the board.
Do a small test before the final cut.

Preparing the wood

Measure the actual thickness of the board with a gauge.
Place the wood on the honeycomb base.
Check that the board is completely flat.
Clamp the wood if it has curvature.
Activate Air Assist and smoke extraction.
Focus the laser correctly on the surface.

Guidelines for xTool 40W

Process	Power	Speed
Passes Fine engraving	20-30%	180-250 mm/s	1
Marking	engraving 35-45%	120-180 mm/s	1
Beech cut 1.5 mm	50-65%	18-25 mm/s	1
Safer cut	65-75%	15-20 mm/s	1

These parameters are indicative. They can vary depending on the wood, humidity, lens condition, and actual machine power.

Recommended

work order

First perform the decorative engraving.
Then cut the inner drafts.
Finally cut the outer contour of the rods.

This order prevents the pieces from moving before finishing the most delicate details.

Cutting

Place the board on the machine.
Check the framing with the frame function.
Start the engraving.
Continue with the inside cuts.
Finish with the outer cut.
Do not move the wood when finished.
Check that all the pieces are completely cut.
If any zone does not separate, repeat the cut without moving the board.

Cleaning and assembly

Remove the rods carefully.
Remove small debris from the fretwork with tweezers.
Arrange the rods in the same position as the layout.
Sand gently with 320 or 400 grit.
Wipe off the dust with a soft brush.
Align the bottom holes.
Place the central pin, screw or rivet.
Adjust the pressure without squeezing too much.
Check that the fan opens and closes correctly.

Final finish

Apply a thin layer of wax, oil or varnish to protect the wood. Prevent the product from accumulating in the drafts. Allow to dry completely before handling the fan.

For a natural finish, wax or oil is recommended. For added protection, use thin-layer satin varnish.

Important

1.5 mm wood is delicate.
Do not force the rods during assembly.
Always use Air Assist.
Run a test before the final cut.
Do not work with bent wood.
Do not squeeze the central axis too much.
Store the fan in a dry place.

Final result

The result is a light, decorative and elegant wooden fan, with an Arabesque design made up of stars, lattices and geometric patterns. A handmade piece created by Calados Vázquez, where wood, design and laser cutting come together in a unique creation.

Brief text for Atomm

Llum d'Alhambra is an arabesque fan made of solid beech wood of 1.5 mm with xTool 40W. Its design combines geometric openwork, ornamental stars and an elegant radial structure. A light, handmade and decorative piece created by Calados Vázquez.

Comments