Rotating Iris Gift Box Laser Cut SVG — Round Iris Gift Box with Rotating Ring, 6-Blade Aperture Lid, 3mm Plywood DXF for xTool & Glowforge

Files
Original files
AuthorxTool · 1/8" (3mm) Basswood Plywood
2
Preview
Preview
Preview
Preview
Add Make Profile
Same design, different machine, material, or any improvement · Earn 100 Credits
Tips for a great Make Profile →
Interlocking parts.

Cut to fit a specific material thickness. If you resize them or change thickness, run Resize slots in Studio first so they still fit together.

gift
1
257

Information

      Rotating Iris Gift Box Laser Cut SVG — Round Iris Gift Box with Rotating Ring (3mm Plywood)

An original, mechanically working gift box: the lid is a real iris diaphragm, not a printed picture of one. Six identical leaves pivot on a fixed pivot ring; a rotating ring with radial drive slots moves all six drive pins together, so the hexagonal opening grows smoothly from about 16 mm across (closed) to about 64 mm across (fully open) as the handle tab sweeps through its 10.89° travel. Drop in jewellery, a ring box, sweets or a small keepsake, then close the iris — no separate lid to lose.

Finished size: 152 mm diameter × 60 mm high; interior about 146 mm diameter × 42 mm deep
Material: 3 mm plywood (or 3 mm MDF with the same settings). All parts fit on one sheet area of 490 × 350 mm — the included sheet layout is already nested.
Design detail: kerf allowance Δk = 0.15 mm is built into every joint and shaft hole (4 mm shafts/dowels run in 4.5 mm holes), so parts fit on a typical diode/CO₂ laser. The ring slots are deliberately wider (5.5 mm) than the 4 mm drive pins so the pins slide freely. If your machine's kerf differs, cut a single test joint first and adjust.

How the mechanism works:
- 6 iris leaves pivot on fixed pivots at radius 48 mm on the pivot ring
- Each leaf's long straight inner edge forms one side of the hexagonal aperture
- The rotating ring's 6 radial slots drive the leaf pins (pin radius 60 → 55 mm) as the ring turns 10.89°
- The handle tab on the rotating ring sticks out past the top ring — push it to open and close
- The lid is held together by 3 M4 lid bolts through the pivot ring, spacer discs and top ring; the leaves and ring slide freely between them

Parts (14 pieces): bottom disc ×1, kerf-bent wall strip ×1, pivot ring ×1, iris leaves ×6, rotating ring with handle tab ×1, spacer discs ×3, top ring ×1.
Hardware required (not included, not cut from sheet): 12× 4 mm dowel pins (6 pivot pins + 6 drive pins, glued flush), 3× M4 bolts + nuts for the lid. Wood glue for the wall lap joint and bottom disc.

Assembly summary: cut a test joint first → bend the wall strip around a round form and glue the 12 mm lap → glue the wall onto the bottom disc → stack the lid (pivot ring, leaves on their dowels, rotating ring with its drive dowels in the slots, spacer discs, top ring) → bolt the lid together and test the travel before tightening fully. Full step-by-step instructions are included (ASSEMBLY.md).

Machines: xTool (D1 / P2 / M1), Glowforge, and any laser cutter or CNC that reads SVG/DXF (LightBurn, K40, OMTech, Epilog…). Glowforge users: use the SVG files.

Files included:
- Individual part files: 7 part types × SVG + DXF (14 pieces total)
- sheet_layout.svg / sheet_layout.dxf — all 14 pieces nested on one 490 × 350 mm sheet area
- ASSEMBLY.md — step-by-step build guide, including the mechanism test
- LICENSE.txt — personal + commercial use of finished physical items; digital files may not be redistributed

Please note: the product images for this listing are digital renders generated from the actual design files — not photographs of a physical item (so what you see is exactly the geometry you cut). This design has been geometrically validated in software, including a full kinematic simulation of the iris travel (dimensions, slot/pin clearances, minimum feature sizes, leaf sweep and bolt clearances); cut a single test joint first to confirm the fit on your machine and material batch, and test the iris travel dry (without glue) before final assembly.
    
Comments

License

This work contains AI-generated content.

You may also like

Wooden Mechanical Iris Box with Rotating Aperture Lid | Laser Cut Vector Files (SVG, DXF)
Atomm Exclusive

Wooden Mechanical Iris Box with Rotating Aperture Lid | Laser Cut Vector Files (SVG, DXF)

lettifi mohamed sabe
lettifi mohamed sabe
3
53
Diaphragm Box

Diaphragm Box

Bill
Bill
89
558
Moire Kinetic Coasters- Hand Spinner
$6.64
$6.64
Credits664

Moire Kinetic Coasters- Hand Spinner

DesignXXStore
DesignXXStore
42
Snowflake Lantern Laser Cut SVG - Wooden Cube Tea Light Lantern with Lift-Off Top Frame, 4 Snowflake Panels, 3mm Plywood DXF for xTool
Atomm Exclusive

Snowflake Lantern Laser Cut SVG - Wooden Cube Tea Light Lantern with Lift-Off Top Frame, 4 Snowflake Panels, 3mm Plywood DXF for xTool

Art of Cnc
Art of Cnc
1
2
Wooden Kitchen Towel Ring Holder Laser Cut SVG - Wall Mounted Open-Top C Ring for 3mm Plywood, DXF
Atomm Exclusive

Wooden Kitchen Towel Ring Holder Laser Cut SVG - Wall Mounted Open-Top C Ring for 3mm Plywood, DXF

Art of Cnc
Art of Cnc
0
0
Coaster Set with Holder Laser Cut SVG - 6 Round Wooden Drink Coasters, Geometric Cut Patterns, 3mm Plywood DXF
Atomm Exclusive

Coaster Set with Holder Laser Cut SVG - 6 Round Wooden Drink Coasters, Geometric Cut Patterns, 3mm Plywood DXF

Art of Cnc
Art of Cnc
0
1
Candy container

Candy container

Joe
Joe
30
160
Waterwheel

Waterwheel

Thomas
Thomas
17
55
Motion Sensor Mount for ZigbeeDevices

Motion Sensor Mount for ZigbeeDevices

wwjd2
wwjd2
2
4
Gift box with lid, laser cut design, table decor. Jewelry box, laser cutting pattern, greeting boxes. Birthday gift, gift for her, laser craft.
$3.99
$3.99
$7.98
Credits399

Gift box with lid, laser cut design, table decor. Jewelry box, laser cutting pattern, greeting boxes. Birthday gift, gift for her, laser craft.

file4laser
file4laser
2
Small square wooden storage box, dimensions 60 x 60 x 57 mm (L x W x H)

Small square wooden storage box, dimensions 60 x 60 x 57 mm (L x W x H)

Raul
Raul
0
1
tangram circulaire

Circular tangram

kalisorciere
kalisorciere
1
7
Gift jewelry box, design laser cutting, circle sliding box. Gift box, laser cut, holiday gift or decor. Table decor, birthday gift, greeting boxes.
$4.79
$4.79
$9.58
Credits479

Gift jewelry box, design laser cutting, circle sliding box. Gift box, laser cut, holiday gift or decor. Table decor, birthday gift, greeting boxes.

file4laser
file4laser
5
Circular coaster with geometric flower petal pattern

Circular coaster with geometric flower petal pattern

Alpha.ARTS
Alpha.ARTS
0
4
Catan Gold or Treasure Tile

Catan Gold or Treasure Tile

Chris
Chris
6
21
Pet Food Bowl Stand Laser Cut SVG - Wooden Raised Single Bowl Stand with Removable Ring & Spill Lip Tray 3mm Plywood DXF for xTool
Atomm Exclusive

Pet Food Bowl Stand Laser Cut SVG - Wooden Raised Single Bowl Stand with Removable Ring & Spill Lip Tray 3mm Plywood DXF for xTool

Art of Cnc
Art of Cnc
0
0
Desk Valet Tray Laser Cut SVG - Wooden Entryway Catch-All Tray with Coin Well and Key Slot, 3mm Plywood DXF for xTool
Atomm Exclusive

Desk Valet Tray Laser Cut SVG - Wooden Entryway Catch-All Tray with Coin Well and Key Slot, 3mm Plywood DXF for xTool

Art of Cnc
Art of Cnc
1
1
Metric Corner Radius Gauge 1–9 mm | Laser Cut Measuring Tool

Metric Corner Radius Gauge 1–9 mm | Laser Cut Measuring Tool

chris2cant
chris2cant
0
2