Report

[Laser cut and engrave] Laser Cut Layered Topographic Map Model in Wood — Project made with S1 machine for Laser cut and engrave.

Grand Canyon 3D Coasters - Bright Angel Trail Layered Topographic Map - Set of 4

Instruction

3 Layered Grand Canyon Project

.xcs

Application scenario

Laser processing (540min)

Machine & module

xTool S1

40W

Compatible xTool Machine

F2 Ultra UV

F2 Ultra（Single）

F2 Ultra

F1 Ultra

F1 Lite

P2S

M1 Ultra

D1 Pro 2.0

D1 Pro

Laserbox

Accessories

xTool S1 Honeycomb Panel

[US Only for xTool S1] xTool Fire Safety Set: Auto Fire Detection, Fire Extinguishing

xTool S1 Riser Base

xTool S1 40W Laser Module

xTool 6-inch 410 CFM Inline Duct Fan

Material used

1/4"(6mm) MDF

1271

Information

This is a project for 3D Coasters for the Grand Canyon's Bright Angel Trail.

A friend of mine hiked this trail and asked if I could make unique coasters for it. I took the topographic map for the Grand Canyon, found the trail, and zoomed into an area that fit the entire path in one screen. After editing the map externally, I moved to XTool and divided a work area into 12 squares sized to a piece of acrylic I had for the top of the coasters - 4 columns of 3 layers. I then divided the elevation of the map into 1/3rds to set onto the 3 layers to give a 3D effect to the coasters. After that, I placed my 1/4" piece of MDF into the S1, lined it all up, and started the laser.

Once the laser finished, I then moved to the table saw to cut the MDF squares straight. I did this to avoid burning the edges of the coasters and having to clean them, but the laser can easily cut these squares perfectly for you if you want darker edges and are okay with cleaning the sides. Then, I simply placed the layers together with fast setting super glue and topped them off with the acrylic to make them a solid coaster. Finally, I added 4 felt pads to the bottom of each to make them table top friendly.

Notes:
* I would recommend using the laser itself to cut the squares because the pieces become so small that the table saw becomes dangerous to use (which you can see how it kicked back at me in the photos and is why some pieces are chipped or have gouges - my friend liked this though as she thought it made it look rugged like the trail)
* When cleaning the burned edges, be sure to clean them before gluing anything or else the ash will stick to the glue and muddy up the result

Instruction

Step1: Gather Materials

Materials:

¼" MDF Sheet - 1/4" x 16" x 12"
4 Acrylic squares (I used these from Amazon) - 0.04" x 3.938" x 3.938"
Quick-setting adhesive (I used liquid super glue)

Step2: Setup Laser

Position your ¼" piece of MDF in your machine
Set your material height
Set your processing area
Confirm with framing

Step3: Start the Laser

This will take a little over 8 hours. The cuts come out clean after 3 passes and the engravings take a while as well because they are set to 180 Lines per cm for added detail

BE SURE TO STAY NEAR THE MACHINE AS THE HIGH POWER AND LOW SPEED GENERATES A LOT OF HEAT/DANGER

Step4: Prepare Material

After the laser has finished, remove the pieces from the machine. Discard the blank cut pieces found between the engraved portions and the borders as these will not be used.

Now would be a good time to clean the edges of the pieces before any adhesive is added to remove any soot/ash from the sides so that they do not stain fingers when grasping the finished product

Step5: Assemble Outside Border

Add a drop of quick-setting adhesive to the back of the border middle layer
1. I have found super glue to work very well with both the MDF and the acrylic
Place the middle layer onto the top of the bottom layer in line with the border
Let it dry enough to hold the piece in place
Repeat steps 1-3 for the top border onto the middle border ensuring all layers are even on the inside and outside

Step6: Assemble Engraved Pieces

Add a drop of quick-setting adhesive to the back of the engraved middle layer
Place the middle layer onto the top of the bottom layer in the correct position
1. Match the bottom edge against the inside border and the engravings to the engravings beneath
Let it dry enough to hold the piece in place
Repeat steps 1-3 for the top layer onto the middle layer
1. There is a very tiny piece at the top layer that represents an “island” that is at the same elevation as the top but is not connected to that cliff in real life. Treat this piece the same as the rest of the top layer

Step7: Add Acrylic Top

Add a sized acrylic piece to the top of the layered coaster
1. Place the adhesive at the edge of the acrylic and MDF to avoid discoloration of the MDF from the moisture of the adhesive

Step8: Add Felt Feet

Add felt feet to the bottom of the coaster. I used 4 pads with a sticky backing at each corner

Step9: Overview

All Steps:

Position your ¼" piece of MDF in your machine
Setup your tool
Let the tool run
Remove your cut/engraved pieces from the machine
Remove the blank pieces between the engraved areas and the borders of the coaster as they will not be used
Add a drop of quick-setting adhesive to the back of the border middle layer
1. I have found super glue to work very well with both the MDF and the acrylic
Place the middle layer onto the top of the bottom layer in line with the border
Let it dry enough to hold the piece in place
Repeat steps 6-8 for the top border onto the middle border
Add a drop of quick-setting adhesive to the back of the engraved middle layer
Place the middle layer onto the top of the bottom layer in the correct position
1. Match the bottom edge against the inside border and the engravings to the engravings beneath
Let it dry enough to hold the piece in place
Repeat steps 10-12 for the top layer onto the middle layer
1. There is a very tiny piece at the top layer that represents an “island” that is at the same elevation as the top but is not connected to that cliff in real life, treat this piece the same as the rest of the top layer
Add a sized acrylic piece to the top of the layered coaster
1. Place the glue at the edge of the acrylic and MDF to avoid discoloration of the MDF from the moisture
Add felt feet to the bottom of the coaster